Schedule

 

 

We have uncovered this great article about Tools You Need to Install a New Bathtub below on the web and accepted it made perfect sense to talk about it with you over here.

Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate speedily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have certified yourself for the task and are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your washroom if you have currently acquired a new bathtub and do not need to transform the arrangement of your previous water system pipelines.
Your tools as well as product checklist must comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area between the tap and the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Setting up the Bathtub

Making use of both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the bath tub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait till the tub has actually been used at the very least once as this will certainly settle it into its last position.

 

 

Planning for the Installation

First of all, the supporting framework provided with the bath must be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last position.

 

 

Tiling Around the Bathtub

In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can split fairly early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an avid person who reads about How to Install a Bathtub, I think sharing that post was worth the trouble. Liked our content? Please share it. Let another person find it. I cherish reading our article about Installing A Bathtub.

Source